Job Description SGS is looking for Structural/Civil Inspectors (Contract) for site locations and shops.
The assignement would start in January 2027 and would be on going.
Locations: Site inspections in Kitimat, BC; shop/vendor inspections across BC and Alberta.
Pay: $75–$90/hour for site work; $55–$60/hour for shop work.
Start: January 2027.
Schedule: Intermittent/as needed—not guaranteed full time hours.
Structural (Shop): verification of structural steel materials, fabrication, welding, surface treatment, erection, and installation to ensure compliance with approved engineering drawings, project specifications, applicable codes, and quality requirements Review approved fabrication drawings, specifications, ITP, QCP, WPS/PQR/WPQ and fabrication procedures Attend kick-off, pre-inspection meetings, witness, surveillance and hold points, as required Verify material grades, MTRs, dimensions, identification, heat numbers and traceability Inspect cutting, beveling, edge preparation, fit-up and dimensional accuracy Review welding procedures and qualifications; inspect fit-up, preheating, welding parameters and workmanship Verify RT, UT, MT and PT activities, procedures, personnel qualifications and reports as specified Check member lengths, profiles, straightness, squareness, hole locations, connection details and tolerances Verify bolt grades, sizes, hole dimensions, nuts, washers and connection arrangements Inspect abrasive blasting, surface cleanliness, surface profile and environmental conditions Verify coating specifications, application, DFT, curing and holiday testing where applicable Verify overall workmanship, identification, marking, preservation, packaging and shipment readiness Prepare detailed reports documenting inspection results, including any issues found.
Recording inspection results and any non-conformities Investigating Non-Conformities identifying causes and assisting in corrective actions.
Structural (Site): Covering steel erection, alignment, bolted connections, field welding, anchor bolts, grouting and structural installation.
Verify delivered structural steel components, identification, traceability and transportation damage.
Inspect anchor bolts, base plates, embedded plates, grout and supporting foundations Verify installation of columns, beams, bracing, trusses, platforms and structural connections Check structural alignment, plumbness, elevations, dimensions and tolerances Verify bolt grades, installation, tightening, pre-tensioning and inspection records.
Verify WPS/WPQ, joint preparation, fit-up, welding workmanship and applicable preheat requirements.
Witness or review field weld NDE activities and reports as required by the ITP Verify changes, repairs and deviations against approved engineering drawings and dispositions Inspect coating damage, surface preparation, touch-up painting, DFT and fireproofing where applicable Verify structural completeness, connection integrity, outstanding deficiencies and final acceptance documentation. CIVIL (Site): monitoring and verifying civil construction activities to ensure compliance with approved engineering drawings, project specifications, applicable codes, construction procedures,
and quality requirements.
Site Preparation and Earthworks Foundation and Reinforcement Inspection Concrete Inspection and Testing Inspection of Underground Utilities and Drainage Inspection of Waterproofing and Protective Systems Experience in soil classification, compaction and field density testing Experience in rebar inspection, formwork and foundation construction Experience in underground piping, drainage, trenching and utility installation Experience with ITPs, QCPs, NCRs, quality documentation and construction surveillance Qualifications Structural CWB-Level 2 with structural steel welding experience Familiarity with CSA , W59, S16, ASTM, ASME IX, SSPC, etc..
Civil/Structural/Mechanical Engineering degree or diploma 5+ years of fabrication and inspection experience at manufacturing shops 5+ years of fabrication and inspection experience at site Experience in fabrication and erection surveillance, ITP implementation, NCR management and quality documentation Civil: ACI Grade I / ICC Reinforced Concrete SI Bachelor's degree or diploma in Civil Engineering or Construction Engineering Technology Minimum 5 years of relevant civil construction inspection experience ACI Concrete Field Testing Technician or equivalent certification Familiarity with CSA / , ACI 318 / 301, etc.
Additional details: Work schedule and hours of work: Intermittent when & where required subject to job requirement Pay Rate (site): $75/hr. to $90/hr. (Shop): $55/hr. to $60/hr.
Per diems (Shop): Expenses will be covered at cost if inspection site is beyond round trip 200 kms from Inspector place of residence and requires overnight stay at hotel Per diems (Site): Expenses will be covered at cost
📌 Structural / Civil Inspector (Contract) (Edmonton)
🏢 SGS
📍 Edmonton