A plant maintenance manager calls at 06:40: the line is down, the PLC shows a fault, the operator has already tried cycling power. You are the person who walks in with the drawings and a meter, finds the cause rather than the symptom, writes the report before you leave, and calls the next morning to confirm the fix held. Between calls you are in the Chilliwack panel shop wiring and point-to-point checking panels, programming and commissioning PLC and HMI systems on water, wastewater, fueling and process projects, and setting up VFDs and instrument loops. If you are a Red Seal electrician who would rather read ladder logic than pull wire, this is the job.

About Vanguard Power Ltd. Vanguard Power Ltd. is a British Columbia-based industrial electrical contractor. Our work includes water and wastewater treatment plants, pump and lift stations, traffic infrastructure, CNG, LNG, hydrogen and petroleum fueling stations, water parks and recreational facilities, and industrial power distribution, instrumentation, and controls projects across BC and Alberta. Our field teams work on live operating facilities, shutdowns, and technically demanding installations that require people who think critically, plan ahead, and take ownership of their work — without needing to be told what to do next.

The Role You keep industrial customers' equipment running and bring new control systems to life. On service calls you diagnose and repair industrial electrical and control faults, decide the diagnostic approach and repair method inside what the customer authorized, make equipment protected, and tell the customer in plain language what was found, what was done and what remains — then write the report the same day. In the panel shop you wire and check control panels to drawing and CSA requirements,



redlining as you go. On projects you program and configure PLC and HMI systems to the approved sequence of operations, run I/O and loop checks, set up VFDs and starters, verify safety circuits, run functional tests with the customer present and hand over programs, backups and as-builts. The Director of Technical Operations holds technical authority for controls across the company; you do the work. You decide program changes inside the approved sequence and like-for-like parts on your own. You never bypass a safety circuit, never change a sequence, interlock or safety function without the Director's approval, never quote a price or promise a date, and never perform extra work the customer or PM has not authorized — you make safe, flag it and recommend.

What You'll Do

Attend service calls across Vanguard's service area: confirm the authorized scope on arrival, diagnose methodically from drawings, sequence of operations, I/O status and measurements, repair or safely isolate, and review the report with the customer before leaving

Program, configure, test, back up and document PLC and HMI systems to the approved sequence of operations, with every program touched backed up to the company project folder the same day

Wire and fabricate control panels in the Chilliwack panel shop to drawing, CSA and CEC requirements,



with point-to-point checks before the panel leaves and redlines kept as changes are made

Troubleshoot motor-control, VFD, instrumentation and automation faults to root cause — a repeat call for the same fault is a job not finished

Support commissioning: I/O and loop checks, motor rotation and bump tests, VFD and soft-starter parameters, safety-circuit verification, functional testing with the customer's representative, punch-list closure on controls scope

Write a service-call report for every call before leaving site — customer, equipment, fault, cause, work performed, parts, time, recommended follow-up — and send it the same day

Enter time daily against the correct project, service call or shop job; reconcile parts used so the customer is invoiced for what was installed; keep test equipment calibrated and software current

Review open calls weekly with the Director of Technical Operations, flag drawing conflicts and extra work in writing, and teach apprentices assigned to controls, panel and troubleshooting work

Take part in the after-hours on-call service rotation [SUBJECT TO DISCUSSION — rotation and call-out terms not yet defined]

Travel [VANGUARD EXPECTATION] Regular travel to customer sites throughout Vanguard's service area in a company vehicle, and to project sites as assigned — including out-of-town and camp-based projects across BC and Alberta when the controls scope requires it — is a condition of employment. Based out of the Chilliwack panel shop between calls and assignments.

What You Bring — Must Have

Demonstrated industrial controls experience: PLC and HMI programming and troubleshooting on at least one major platform (Allen-Bradley / Rockwell, Siemens or comparable), motor control and VFD setup

📌 Industrial Automation Specialist (Winnipeg)
🏢 Vanguard Power
📍 Winnipeg